SB2 OPTION

-Side Bar to clear stock door panel and arm rest-
(shown above)

** PURCHASED WITH KIT...$39.95/pr.
** PURCHASED SEPARATELY...$67.95/pr.

SB3 OPTION

-Road Race side bar-

** PURCHASED WITH KIT...$29.95pr.
** PURCHASED SEPARATELY...$55.95/pr.

SB4 OPTION

-Swing Out side bar KIT-

** PURCHASED WITH KIT...$62.00/side
** PURCHASED SEPARATELY...$66.95/side

NOTE:Used when you want easy access getting into the car, just pull quick pin and swing the bar out of the way!! EASY!! These kits are the weld
on "saddle" mount type. "Safer and Stronger"
than other types and will resist the
tendency to shear the pin upon impact.
***
NOTE: side bars may be removed with this kit!
You need one kit per side bar!

SB5 OPTION

-"M" Bar side bar (easy entry)-

** PURCHASED WITH KIT...$49.95/pr.
** PURCHASED SEPARATELY...$72.95/pr.

SB6 OPTION

-X-Brace DOOR-

** PURCHASED WITH KIT...$39.95/pr.
** PURCHASED SEPARATELY...$55.95/pr.
**
Add to exsiting side bars.
Consists of 4 pieces, enough
to do both sides. Some
pre-notching already done!

SB7 OPTION

-"Helmet Bar" side bar (all out competition)-

** PURCHASED WITH KIT...$25.00
** PURCHASED SEPARATELY...$33.00

SB8 OPTION
(pic same as above)

-Rocker Bar side bar (competition)-
*one side notched.
Runs along the rocker panel,
from a-pillar to main hoop.

** PURCHASED WITH KIT...$22.00
** PURCHASED SEPARATELY...$24.00

***
**SB9 OPTION...BENT "PICKUP" REAR BRACES.
Straight rear braces come standard
in our roll bar kits, but this
option makes installation of the
rear braces for pickup
trucks easier. It allows the rear
braces to exit the cab "straight out"
instead of at an angle for easier
installation.
**
When purchased with RB or RC kit......$44.95
When purchased separately.............$72.95
(shown below)







SB10 OPTION....X BRACE BEHIND DRIVER
Some of the pre-notching
already done!
Purchased with kit.....$45.00
purchased separately...$61.95
**
Full Size Trucks.......$72.95

BB2 NOTCHBACK OPTION

-Designed to clear back seat on certain cars-

** PURCHASED WITH KIT...$39.95
** PURCHASED SEPARATELY...$67.95

BB3 NOTCHBACK OPTION

-Designed to clear back seat on certain cars-

** PURCHASED WITH KIT...$39.95
** PURCHASED SEPARATELY...$67.95

BB4 HATCHBACK OPTION

-Designed to clear back seat on hatchback cars-

** PURCHASED WITH KIT...$39.95
** PURCHASED SEPARATELY...$67.95

PRE-NOTCH OPTION
(prefit tubing ends)
**
NOTE: With this option,
all possible places are
notched with the exception
that some have to be fitted
upon installation.

** Still only...
An additional...$20.00
***

ROAD COURSE OPTION

-This OPTION uses the Larger (1-3/4" OD tubing).
Our standard roll cages are made
from the 1 5/8"ERW tubing. This
option is for some road course race
cars that do not require the DOM or
seamless tubing.
***

** for the 10 or 12 pnt....Additional...$50.00
***
** For DOM tubing an additional cost
will be incurred.

CHROMOLY OPTION

-Chromoly (4130) is
approx. 35% lighter than
its mild steel counterpart,
and must be TIG WELDED!!

** 4 pt. roll bar...add $110.00
** 6 pt. roll bar...add $160.00
** 8 pt. roll bar...add $175.00
**10 pt. roll cage...add $245.00
**12 pt. roll cage...add $275.00
**14 pt. roll cage...add $322.00

ROLL BAR/CAGE UPGRADE OPTION

-PURCHASED SEPARATELY-
These upgrades are used when
adding to your exsisting
roll bar that is already
welded in the car.

** 4 to 6 pt...(pre-notched)...$67.95
** 6 to 8 pt...(pre-notched)...$33.95
** 8 to 10 pt...$123.95
** 10 to 12 pt...$83.95
** 12 to 14 pt...$61.95

"EXTRA" FLOOR PLATES...
Each roll bar and cage kit
for unibody cars come standard
with 6 (six) floor plates. BUT if you
want extra plates, they are available.
***
EXTRA 6"X6" FLOOR PLATES
part#8021...floor plate..$3.75 ea

"NEW"
***A-PILLAR BARS***
For many applications we have "BOTH",the bars that
go "THROUGH" the Dash, and the bars that stand up BEHIND the Dash for easier Roll cage installation.
On a few applications there is an optional charge of $20 because of the complexity of the piece.

**IF AN OPTION IS PURCHASED WITH A KIT, THE KIT MUST BE A ROLL BAR OR CAGE KIT **


**MEASURING for
ROLL BARS and CAGES**

If you don't see a roll bar on this site for your particular application, here is a way that you can help us bend a custom cage for you. Below are drawings with the dimensions areas indicated, that we would need to bend up a cage for you. Just print off the sheet and fill in the cicles with the appropriate dimensions and "fax" it or "email" it back to us.






*EXTRA ROLL BAR AND CAGE PARTS*
For replacement or repairs
Click here!