Auto Weld's 4-LINK JIG WELDED CLIP KITS are made from the highest quality materials and of the highest quality construction. The frame rails are made from 2x3x11ga steel tubing. Not made from the inferior (.083 wall). They are bent with "NO WRINKLE TECHNOLOGY" and are expertly welded to make these frames the toughest and best looking on the market today. Check out the standard features in our kits!!! (features you would pay extra for from our competitors) Our kits come complete with rod ends, 2x3x11ga steel tubing for frame connectors, and we offer any width up to 33". Our kits are the easiest to install, are pleasing to the eye, and best of all, they work!!
***
NOW AVAILABLE: 2X4 REAR FRAME CLIPS!!!
(Ultimate II shown directly below)
***
CHECK OUT OUR QUALITY BELOW!!!
















TIP**
When you are preparing to order a Jig Welded
frame clip, you will need to know:
**the wheels and tires that you are going to use
(or) the dimensions for both.

**what frame width you will need.
**what is the rear width.
**What is the height of the "rocker to the ground" in front of the rear tire.
**And what is the outside tire diameter...
or....rear tire height.






***DIMENSIONS***
This dimension drawing may help in determining how wide the frame and the rear should be.
A....FRAME RAIL WIDTH
B....TOTAL REAR WIDTH (back of
wheel to back of wheel)
**Deduct rotor or drum
thickness to calculate
"axle to axle" width.
C....INSIDE FENDER LIP TO INSIDE LIP
(measured over axle centerline)
D....TOTAL TRACK WIDTH
E....TOTAL BACKSPACE (backspace of wheel
plus the bulge of the tire)
F....WIDTH OF WHEEL AND TIRE (inflated)
G....CLEARANCE BETWEEN FENDER LIP AND
SIDEWALL OF TIRE
H....CLEARANCE BETWEEN FRAME RAIL AND
TIRE SIDEWALL
I....WHEEL WIDTH (measured between the
inside lips of the wheels)
J....BACKSPACE OF WHEEL (measured from
the back edge of the rim to the
back where the wheel contacts the
axle)
ADDED NOTE: When calculating "total rear
width",, add a 1/2" to each
side of the wheel's width.
(Example: A 15" wide wheel is actually
16" measured at the outside
lips of the wheel. Use this
as a rule of thumb.
Remember!..the wheel's
backspace is also measured
from this outside point.



!! IF YOU NEED HELP WITH THE DIMENSIONS, WE WILL BE GLAD TO ASSIST YOU !!
back to top



**OPTIONS**

OPTION ONE FEATURES:

-Jig welded frame assembly,
made from the "better" 2x3x11ga
box steel tubing! Not the inferior
.083 wall tubing.
-Competition 4-link
-All (8) Chromoly "HD" rod ends
-Series 7000 coilovers
-Diagonal track locator
-All hardware
-Frame connector material
*Very Complete*
***
2x3 Rear Frame and Suspension clip
Part#3520.......$1668.95
***
2x4 Rear Frame and Suspension clip
with "Oval" crossmember included
Part#3521.......$2093.95
**
COILOVER UPGRADES:
Aldan (single adjustable) upgrade
Part#7065..add...$195.00
Aldan (double adjustable) upgrade
Part#7066..add...$320.00
QA1 (single adjustable) upgrade
..add..$215.00
QA1 (double adjustable) upgrade
..add..$355.00



***
Frame only,2x3 fixture welded with
all mounts fully welded,
Part#3515.........$944.95(shown below)







***
Frame only,2X4 fixture welded with
all mounts fully welded
with "Oval" crossmember included
Part#3516.........$1,299.95




OPTION TWO FEATURES:

-Jig welded frame assembly (same as above)
-Competition 4-link
-All (8) chromoly(HD)rod ends
-Aldan coilovers (single adjustable)
QA1 available at additional cost!
-Reverse wishbone track locator
-New Jig welded rear housing,
w/3 1/4"x1/4" DOM axle tubes,
w/brace
-All hardware
-Frame connector material


*2x3 rear clip*
(discounted)over $200
Part#3525.........$2739.95
***
*2x4 rear clip*
(discounted) over $200
with "Oval crossmember included
Part#3526.........$3144.95





"EXTREME STRENGTH"
COMPETITION 4-LINK REAR CLIP
(above)and(below)
Features: jig welded mandrel bent
frame assembly made from 2x3x11ga steel
tubing, "Aldan" single adjusting
coilovers, wishbone track locator,
HD Chromoly 1 1/4" dia. 4-link tubes,
( 1 3/8" diameter optional)...
(SHOWN ABOVE)
New massive and thicker aftermarket
9" Ford housing (or Fabricated housing)
with 3 1/4" x 1/4" DOM steel axle
tubes, brace, fill and drain,
all 8 HD chromoly
rod ends, frame connector material,
Moser race axles(up to 35 spline
for same price), bearings, 3" studs,
retainers and all hardware.
18"-33" widths!
**
COILOVER UPGRADES:
Aldan (double adjustable)upgrade
add $125.00
QA1 (single adjustable) upgrade
add $20.00
QA1 (double adjustable) upgrade
add $155.00






Part#3535...$3334.00 (discounted) SAVE
(2x3 rear clip)
Part#3536...$3734.00 (discounted) SAVE
(2x4 rear clip w/oval x-member)
***
NOTE: Race axles included, but not
shown in picture right above.
***
(Also Shown Above)
*Exhaust port option...$125
*3/4" Anti-rollbar option...$375
*1" Anti-rollbar option...$475
*Wheelie bar brackets installed...$75
****
"Wilwood" Racing Brakes
(for above rear clips)
Part#AW0261 (big Ford)........$486.95
Part#AW2119(big new)........$486.95

back to top





**TWO OPTIONS**

--Ultimate II clips are best used for cars & trucks running down near and in the 9 second zone, and being driven everyday as well.--


OPTION ONE FEATURES:

-Jig welded frame assembly
Made from the "Better" 2x3x11ga
steel tubing, not the inferior
.083 wall stuff.
-Ultimate II 4-link
-All 8 polyurethane rod ends
-Series 7000 coilovers
-Panhard track locator
-All hardware
-Frame connector material
**
COILOVER UPGRADES:
Aldan (single adjustable) upgrade
Part#7065..add..$195.00
Aldan (double adjustable) upgrade
Part#7066..add..$$320.00
QA1 (single adjustable) upgrade
..add...$215.00
QA1 (double adjustable) upgrade
..add...$355.00

2x3(discounted)
Part#3500.........$1543.95
***
2x4 w/oval crossmember)
Part#3501.........$1918.95
**
Frame only, 2x3 fixture welded with all mounts
fully welded
Part#3400.........$944.95
***
Frame only, 2x4 fixture welded with all mounts
fully welded w/oval crossmember
Part#3401.........$1299.95
(shown below)

OPTION TWO FEATURES:

-Jig welded frame assembly
(same as above)
-Ultimate II 4-Link
-All 8 polyurethane rod ends
-Aldan coilovers
QA1 available at additional cost!
-Wishbone track locator
-New Jig welded 9" Ford housing
with 3 1/4"x1/4" DOM steel
axle tubes and brace
-All hardware
-Frame connector material

***
ABOVE: package with "2x3" rails
(discounted/SAVE!)
Part#3510 ...ONLY.....$2639.95
***
BELOW: same package but "2x4" rails
with "Oval" crossmember included!
Part#3511 ...ONLY.....$2964.95
(wishbone not shown but included)
***
(options that are shown below)
Add: fill and drain...$68
Add: Moser axles...$360 pair
W/BSR pkg...$99.00
***
COILOVER OPTIONS:
Aldan (double adjustable) upgrade
add $125.00
QA1 (single adjustable) upgrade
add $20.00
QA1 (double adjustable) upgrade
add $155.00




The NEW 2x4 rear clips include all
the standard features of our
2x3 rear clips except they are
made out of the 2x4 material for
extra strength and where a rollbar
is not desired. We use our "NO-
WRINKLE" technology when making
our rails so you get the highest
quality product you can purchase!!
***
Shown above....a standard "Ultimate II"
4-link-2x4 rear clip, but with the single adjust
Aldan coilovers (QA1 additional!) , housing brace,
fill and drain, Moser axles,w/BSR pkg options.
****
Shown below....a standard "Ultimate II"
4-link-2x4 rear clip, but with the
"wheelie bar, wishbone track locator,
Oval-crossmember, anti-rollbar ,
housing brace, fill and drain options.
***





***
*CLICK HERE*
for
*FULL CHASSIS*
***




TYPICAL SIDEVIEW OF "REAR CLIP"
**4-LINK**



This is a typical drawing of a rear clip that shows some basic positioning of our 4-Link packages.
It is based on a 32"dia. tire.
DIMENSION "A"
Competition 4-Link........(approx..26 1/4"
Ultimate II (Pro-street)..(approx..23 1/4"
DIMENSION "B"
Competition 4-link........(approx..21 1/2"
Ultimate II (Pro-street)..(approx..18 3/4"
LINKS...bolt to bolt measurement
Competition 4-Link.........21"
Ultimate II (Pro-street).......18"

***
"LOW PROFILE 4-LINK"


***
Below is a custom AUTO WELD
clip designed for an '80 Dodge
full size pickup. It features our
typical "Low Profile" 4-link,
panhard bar, Series 7000 coilovers,
housing and axle package.
***
This is an example of some of the
custom clips we can design and build.



We also use this "LOW PROFILE" 4-link
when building our S10 rear clips.
**
CLICK HERE FOR MORE "S10" INFO.

home